Can broken valve springs and defective valve stem seals be replaced without removing the cylinder heads in four cylinder engine on Chrysler Cirrus?

Broken valve springs and defective valve stem seals can be replaced without removing the cylinder heads, typically requiring two special tools and a compressed air source. Begin by removing the valve cover and the spark plug from the affected cylinder, or all spark plugs if replacing all valve stem seals. Turn the crankshaft until the piston in the affected cylinder is at top dead center on the compression stroke, and if replacing all seals, start with cylinder number one, working through the firing order. Thread an adapter into the spark plug hole and connect an air hose from a compressed air source; many auto parts stores supply the necessary adapter. Remove the rocker arms and apply compressed air to the cylinder. Stuff clean shop rags into the cylinder head holes above and below the valves to prevent parts and tools from falling into the engine, then use a valve spring compressor to compress the spring and remove the keepers with small needle-nose pliers or a magnet. Remove the spring retainer and valve spring, then take out the valve guide seal/spring seat assembly, being cautious that if air pressure fails to hold the valve closed, the valve face or seat may be damaged, necessitating cylinder head removal for further repairs. Wrap a rubber band or tape around the top of the valve stem to prevent it from falling into the combustion chamber, then release the air pressure. Inspect the valve stem for damage, ensuring it rotates freely in the guide without binding; if it does bind, the valve may be bent or the guide damaged, requiring head removal for repair. Pull up on the valve stem to close it, reapply air pressure to retain it in the closed position, and then remove the tape or rubber band. Lubricate the valve stem with engine oil and install a new valve guide seal/spring seat assembly, tapping it into place with a deep socket. Position the spring over the valve, install the valve spring retainer, compress the spring, and carefully position the keepers in the groove, applying a small dab of grease to hold them if necessary. Remove the pressure from the spring tool and ensure the keepers are seated, then disconnect the air hose and remove the adapter from the spark plug hole. If applicable, install the spark plug tubes for 2.0L engines, followed by the rocker arms, spark plug(s), and wire(s). Finally, install the valve cover, start the engine, and check for oil leaks and unusual sounds from the valve cover area.

OEM Chrysler Valve Stem Seal

Engine Valve Seal

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

19 Valve Stem Seals found

View related parts
Chrysler Valve Seals Part Number: 5037798AA
$12.83 MSRP: $18.95
You Save: $6.12 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Valve Guide; Valve Stem Seal; Seal Valve Guide
Fits the following Chrysler Models:
- 300 | 2005-2010 | C SRT8 | 8 Cyl 6.1 L GAS
View related parts
Chrysler Valve Seals Part Number: MD307342
$1.86 MSRP: $3.00
You Save: $1.14 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Valve Guide; Valve Stem Seal; Seal, Exhaust Valve Stem; Seal Valve Guide
Fits the following Chrysler Models:
- Cirrus | 1995-2000 | LX, LXi | 6 Cyl 2.5 L GAS
- Sebring | 2001-2005 | LX, LXi, Limited | 6 Cyl 3.0 L GAS
View related parts
Chrysler Valve Seals Part Number: 2222425000
$8.74 MSRP: $13.10
You Save: $4.36 (34%)
ADD TO CART
Product Specifications
- Other Name: Seal - Valve Guide; Valve Stem Seal; Seal Valve Guide
Fits the following Chrysler Models:
- 200 | 2011-2014 | LX, Limited, Touring | 4 Cyl 2.4 L GAS
- Sebring | 2007-2010 | Base, LX, Limited, Touring | 4 Cyl 2.4 L GAS
View related parts
Chrysler Valve Seals Part Number: 5047453AA
$6.19 MSRP: $9.20
You Save: $3.01 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Valve Guide; Valve Stem Seal; Seal Valve Guide
Fits the following Chrysler Models:
- 200 | 2015-2017 | C, LX, Limited, S | 4 Cyl 2.4 L GAS
View related parts
Chrysler Valve Seals Part Number: 4648619
$6.34 MSRP: $8.03
You Save: $1.69 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Valve Guide; Seal, Valve Stem Standard-0.15Mm Outside; Valve Guide .015" Oversize; Valve Guide/Spring.
Fits the following Chrysler Models:
- Cirrus | 1999-2000, 1995-1997 | LX, LXi | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- PT Cruiser | 2001-2008 | Base, Dream, Dream Cruiser, GT, LX, Limited, Street Cruiser, Touring | 4 Cyl 2.4 L GAS
- Sebring | 2001-2006, 1995-1999 | Base, JX, JXi, LX | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Voyager | 2000-2003 | Base, Ec, LX | 4 Cyl 2.4 L GAS
View More
View related parts
Chrysler Valve Seals Part Number: 53021974AA
$11.14 MSRP: $16.20
You Save: $5.06 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Valve Guide; Valve Stem Seal; Seal Valve Guide
- Replaces: 53020752AD
Fits the following Chrysler Models:
- Aspen | 2007 | Limited | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
Chrysler Valve Seals Part Number: 53021578AA
$10.96 MSRP: $15.90
You Save: $4.94 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Valve Guide; Valve Stem Seal; Seal Valve Guide
Fits the following Chrysler Models:
- 300 | 2005-2010 | C, C SRT8 | 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
- Aspen | 2007-2008 | Limited | 8 Cyl 5.7 L GAS
View related parts
Chrysler Valve Seals, Black/Brown Part Number: 5048025AA
$3.35 MSRP: $4.95
You Save: $1.60 (33%)
ADD TO CART
Product Specifications
- Other Name: Seal - Valve Guide; Valve Stem Seal; Seal Valve Guide Black and Brown are interchangeable; use all one color on the cylinder head.
Fits the following Chrysler Models:
- 300 | 2011-2023 | Base, C, C Luxury, C Platinum, Limited, S, Touring, Touring L | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
- Pacifica | 2017-2024 | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Platinum, Hybrid Premium, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Hybrid Touring Plus, L, LX, Limited, Pinnacle, Touring, Touring L, Touring L Plus, Touring Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
- Voyager | 2020-2024 | L, LX, LXi | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View More
View related parts
Chrysler Valve Seals, Black/Brown Part Number: 5184168AB
$9.40 MSRP: $13.50
You Save: $4.10 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Valve Guide; Valve Stem Seal; Seal Valve Guide Black and Brown are interchangeable; use all one color on the cylinder head.
Fits the following Chrysler Models:
- 200 | 2011-2017 | C, LX, Limited, S, Touring | 6 Cyl 3.6 L FLEX
- Town & Country | 2011-2016 | 30th Anniversary Edition, LX, Limited, Limited Platinum, S, Touring, Touring L | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Valve Seals Part Number: 53022090AB
$11.69 MSRP: $17.35
You Save: $5.66 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Valve Guide; Valve Stem Seal; Seal Valve Guide Not Included; Quantity Is Per Cylinder Head.
Fits the following Chrysler Models:
- 300 | 2009-2023 | C, C Luxury, C Platinum, S, SRT8, SRT8 Core | 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
- Aspen | 2009 | Limited, Limited Hybrid | 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.7 L GAS
View related parts
Chrysler Valve Seals Part Number: 5086290AA
$7.86 MSRP: $26.20
You Save: $18.34 (70%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Valve Guide; Valve Stem Seal; Seal Valve Guide
- Replaces: 5080057AA, 5080058AA
Fits the following Chrysler Models:
- Crossfire | 2004-2008 | Base, Limited, SRT-6 | 6 Cyl 3.2 L GAS
View related parts
Chrysler Valve Seals Part Number: MD197467
$2.16 MSRP: $12.40
You Save: $10.24 (83%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Valve Stem; Valve Stem Seal; Seal, Valve Stem (Rubber); Seal Valve Guide; Seal, Valve Stem
Fits the following Chrysler Models:
- Conquest | 1987-1989 | Base, TSi | 4 Cyl 2.6 L GAS
- E Class | 1984 | Base | 4 Cyl 2.6 L GAS
- Executive Limousine | 1985 | Base | 4 Cyl 2.6 L GAS
- Executive Sedan | 1984 | Base | 4 Cyl 2.6 L GAS
- Grand Voyager | 2000 | Base, SE | 6 Cyl 3.0 L GAS
- LeBaron | 1990-1994, 1984-1985 | Base, GT, GTC, High Line, LE, LX, Landau, Mark Cross, Premium | 4 Cyl 2.6 L GAS, 6 Cyl 3.0 L GAS
- New Yorker | 1989, 1984-1985 | Base, Landau | 4 Cyl 2.6 L GAS, 6 Cyl 3.0 L GAS
- TC Maserati | 1990-1991 | Base | 6 Cyl 3.0 L GAS
- Town & Country | 1990, 1984-1985 | Base, Mark Cross | 4 Cyl 2.6 L GAS, 6 Cyl 3.0 L GAS
- Voyager | 2000 | Base | 6 Cyl 3.0 L GAS
View More
View related parts
Chrysler Valve Seals Part Number: 4781072AB
$7.32 MSRP: $10.75
You Save: $3.43 (32%)
ADD TO CART
Product Specifications
- Other Name: Seal - Valve Guide; Valve Stem Seal; Seal Valve Guide
Fits the following Chrysler Models:
- Pacifica | 2005-2007 | Base | 6 Cyl 3.8 L GAS
- Town & Country | 2001-2010 | Base, EL, EX, LX, LXi, Limited, Touring, Touring Plus, Walter P. Chrysler Signature Series | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
- Voyager | 2001-2003 | Base, LX | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
View More
View related parts
Chrysler Valve Seals Part Number: MD184303
$2.85 MSRP: $4.60
You Save: $1.75 (39%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Valve Guide; Valve Stem Seal; Seal, Inlet Valve Stem (Rubber); Seal, Exhaust Valve; Seal, Intake Valve; Seal Valve Guide
Fits the following Chrysler Models:
- Cirrus | 1995-2000 | LX, LXi | 6 Cyl 2.5 L GAS
- Sebring | 2001-2005 | Base, LX, LXi, Limited | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
Chrysler Valve Seals Part Number: 4892292AA
$14.47 MSRP: $19.15
You Save: $4.68 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Valve Guide; Seal Valve Guide
- Replaces: 4792319, 4663002
Fits the following Chrysler Models:
- 300 | 2005-2010 | Limited, S, Signature Series, Touring | 3.5L V6, 6 Cyl 3.5 L GAS
- 300M | 1999-2004 | Base, Pro-Am, Special | 3.5L V6, 6 Cyl 3.5 L GAS
- Concorde | 1993-2004 | Base, LX, LXi, Limited | 3.2L V6, 3.5L V6, 6 Cyl 3.2 L GAS, 6 Cyl 3.5 L GAS
- LHS | 1999-2001, 1994-1997 | Base | 3.5L V6, 6 Cyl 3.5 L GAS
- New Yorker | 1994-1996 | Base | 3.5L V6, 6 Cyl 3.5 L GAS
- Pacifica | 2004-2008 | Base, LX, Limited, Touring | 3.5L V6, 6 Cyl 3.5 L GAS, 6 Cyl 4.0 L GAS
- Prowler | 2001-2002 | Base | 3.5L V6, 6 Cyl 3.5 L GAS
- Sebring | 2007-2010 | Limited | 3.5L V6, 6 Cyl 3.5 L GAS
- Town & Country | 2008-2010 | Limited, Touring, Touring Plus | 6 Cyl 4.0 L GAS
View More
View related parts
Chrysler Valve Seals Part Number: 4071003
$7.15 MSRP: $10.60
You Save: $3.45 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal; Valve Stem Seal; Exhaust Valve Seals; Seal, Intake Valve Stem, Oil (1988); Shield, Valve Stem Oil Exhaust; Seal, Intake Valve Stem Oil
Fits the following Chrysler Models:
- Fifth Avenue | 1984-1989 | Base | 8 Cyl 5.2 L GAS
View related parts
Chrysler Valve Seals Part Number: 4663904
$7.78 MSRP: $15.25
You Save: $7.47 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Valve Guide; Valve Stem Seal; Seal Valve Guide
Fits the following Chrysler Models:
- 300 | 2005-2010 | Base, LX, Touring | 6 Cyl 2.7 L GAS
- Concorde | 1998-2004 | LX | 6 Cyl 2.7 L GAS
- PT Cruiser | 2009 | Base, LX, Limited, Touring | 4 Cyl 2.4 L GAS
- Sebring | 2001-2010 | Base, GTC, LX, LXi, Limited, TSi, Touring | 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View More
View related parts
Chrysler Valve Seals Part Number: 4201332
Product Specifications
- Other Name: Seal - Valve Guide (Intake/Exhaust); Valve Stem Seal; Valve Spring; Valve Springs; Seal, Valve Guide - Standard Edm Engine; Standard Valve Guide options available.
Fits the following Chrysler Models:
- Concorde | 1993-1996 | Base, LX | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
- E Class | 1984 | Base | 4 Cyl 2.2 L GAS
- Grand Voyager | 2000 | Base, SE | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
- Imperial | 1990-1993 | Base | 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
- Laser | 1984-1986 | Base, XE | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS
- LeBaron | 1984-1993 | Base, GT, GTC, GTS, High Line, LE, Landau, Mark Cross, Premium | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS
- New Yorker | 1990-1993, 1984-1988 | Base, Fifth Avenue, Landau, Salon, Turbo | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
- TC Maserati | 1989 | Base | 4 Cyl 2.2 L GAS
- Town & Country | 1990-2000, 1984-1988 | Base, LX, LXi, Limited, Mark Cross, SX | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
- Voyager | 2000 | Base, SE | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
View More
View related parts
Chrysler Valve Seals Part Number: 4071006
Product Specifications
- Other Name: Shield - Valance Stem Oil Exhaust; Valve Stem Seal; Exhaust Valve Seals; Seal, Intake Valve Stem, Oil (1988); Shield, Valve Stem Oil Exhaust
Fits the following Chrysler Models:
- Fifth Avenue | 1984-1989 | Base | 8 Cyl 5.2 L GAS

Chrysler Valve Stem Seal

OEM parts sourced directly from Chrysler deliver superior quality, long lasting strength, and a precise fit you can trust. Each item goes through strict quality checks to ensure safety, toughness, and performance that matches your factory equipment. At JeepPartsDeal online shop, you'll get top-quality, budget-friendly OEM Chrysler Valve Stem Seal for your vehicle. We focus on giving you a high standard without pushing up the price. Our full selection of genuine factory products comes backed by the original manufacturer's warranty. You'll love our fast delivery, seamless shopping experience, and convenient return policy, saving you all the hassle.

Chrysler Valve Stem Seal prevents the entry of oil in the combustion chambers and allows the valves to move freely. Chrysler reduced engine shake since 1925 with Floating Power and made vehicles that did not shake on rough roads, showing that smart mechanical concepts could actually translate into sensible calmness on the road. With wide body lines chasing after airflow and allowing their cabins to breathe more freely, reducing wind noise and proving to everyone that good appearance is important in the world when it makes the ride easier and more comfortable, Chrysler did it. Next, Chrysler came with the first realistic minivan, scooting families inside with low levels, sliding doors, and an open-air cabin that allowed weekend gear to have a spot of its own. Chrysler maintains the purchasing process straightforward, prices genuine, and cabins adjusted to long journeys, hence drivers press the start and think that the car already knows what they want to do. The Valve Stem Seal is a narrow ring that fits around the valve guide, preventing the flow of hot oil into the combustion chamber but allowing the stem to move freely in order to maintain a controlled level of lubrication and lower consumption. The Valve Stem Seal is heat tough rubber coupled with accurate lip geometry, which shrugs off high temperature spikes and long periods of idle time that scar inferior seals. The Valve Stem Seal is installed with tolerances of factory fit, remains stationary during years of stop and go, and prevents tailpipes from remaining clearer as oil is denied an opportunity to burn.

Chrysler Valve Stem Seal Parts and Q&A

Valve Seals
4648619
Q: Can broken valve springs and defective valve stem seals be replaced without removing the cylinder heads in four cylinder engine on Chrysler Cirrus?
A:
Broken valve springs and defective valve stem seals can be replaced without removing the cylinder heads, typically requiring two special tools and a compressed air source. Begin by removing the valve cover and the spark plug from the affected cylinder, or all spark plugs if replacing all valve stem seals. Turn the crankshaft until the piston in the affected cylinder is at top dead center on the compression stroke, and if replacing all seals, start with cylinder number one, working through the firing order. Thread an adapter into the spark plug hole and connect an air hose from a compressed air source; many auto parts stores supply the necessary adapter. Remove the rocker arms and apply compressed air to the cylinder. Stuff clean shop rags into the cylinder head holes above and below the valves to prevent parts and tools from falling into the engine, then use a valve spring compressor to compress the spring and remove the keepers with small needle-nose pliers or a magnet. Remove the spring retainer and valve spring, then take out the valve guide seal/spring seat assembly, being cautious that if air pressure fails to hold the valve closed, the valve face or seat may be damaged, necessitating cylinder head removal for further repairs. Wrap a rubber band or tape around the top of the valve stem to prevent it from falling into the combustion chamber, then release the air pressure. Inspect the valve stem for damage, ensuring it rotates freely in the guide without binding; if it does bind, the valve may be bent or the guide damaged, requiring head removal for repair. Pull up on the valve stem to close it, reapply air pressure to retain it in the closed position, and then remove the tape or rubber band. Lubricate the valve stem with engine oil and install a new valve guide seal/spring seat assembly, tapping it into place with a deep socket. Position the spring over the valve, install the valve spring retainer, compress the spring, and carefully position the keepers in the groove, applying a small dab of grease to hold them if necessary. Remove the pressure from the spring tool and ensure the keepers are seated, then disconnect the air hose and remove the adapter from the spark plug hole. If applicable, install the spark plug tubes for 2.0L engines, followed by the rocker arms, spark plug(s), and wire(s). Finally, install the valve cover, start the engine, and check for oil leaks and unusual sounds from the valve cover area.