How to Service and Repair the Fuel Level Sensor on the Left Side Module on Dodge Charger?

Before working on the left side module's fuel level sensor, you must loosen the fuel pressure and remove the negative battery cable. Make sure not to let the fuel go higher than 5/8 of the tank's capacity before removing the module lock-ring. Loop a 30-inch long nylon tube with a 30-degree cut over the check valve on the tank to drain only part of the fuel. Take off the backmost lower seat cushion by pushing it back and lifting it all the way up and then fold the foam pad above the access cover for the modules back as well. Take the electrical connector off the left side module and mark how it should be placed. Loosen the left side module lock ring using special tool #9340 and then push the hose into the fuel tank from above to empty the left side fuel. Release the electrical connectors of both side fuel level sensors and lift off the top half of the module to tilt the bottom half and remove any remaining fuel. Pull the wire out of the sensor module and use a screwdriver to lift the level sensor straight up and remove it from the module. Reinstall the level sensor with the locking tabs secure, route the wires where they belong and mount the module top on top of the bottom. Secure the electrical connections from the right fuel level sensor, the left module sensor and the fuel pump and use the marks to ensure the module is facing correctly as you secure it with special tool #9340. Reattach the left side electrical connector, place the plastic access cover over it and next, fold the seat pad back and insert the lower seat cushion at the back. Fill the tank with fuel, hook the negative battery cable back up and scan the car while pushing the pressure on the fuel system to look for specific problems.

How to Remove and Install a Fuel Level Sensor from the Fuel Pump Module on Dodge Ram 1500?

Both the fuel level sending unit and the float assembly are part of the fuel pump module and can be found on its side. First, take out the fuel pump module before removing the fuel level sensor from the fuel tank. Then, holding the plastic tab in an open position, slowly slide the assembly to the back to separate the sending unit from the pump module. Undo the 4-wire connector from the fuel pump module and pull out the wires needed from this connector using a terminal pick/removal tool. To install the mixer, join the wire connections to the electrical connectors and put the 4-wire electrical connector onto the pump module. Step 2: Place the sending unit above the pump, slide and snap it and then connect the fuel pump module.

OEM Dodge Fuel Level Sensor

Gas Gauge Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

145 Fuel Level Sensors found

View related parts
Dodge Fuel Gauge Sending Unit Part Number: 68042937AA
$71.33 MSRP: $147.00
You Save: $75.67 (52%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Level Unit; Fuel Pump Module Assembly; Fuel Level Sensor; Fuel Pump Module; Level Sensor; Module Kit Level Unit
Fits the following Dodge Models:
- Avenger | 2011-2014 | Express, Lux, Mainstreet, SE, SXT
View related parts
Dodge Fuel Pump Part Number: 68079472AA
$209.69 MSRP: $460.00
You Save: $250.31 (55%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Fuel Pump/Level Unit; Electric Fuel Pump; Fuel Pump Module Assembly; Fuel Sending Unit; Fuel Pump Module; Fuel Pump Assembly; Module Kit Fuel Pump/Level Unit Package Contain: Fuel Pump Module Sending Unit And O - Ring
- Replaces: RL079472AA
Fits the following Dodge Models:
- Ram 2500 | 2010 | Laramie, SLT, ST, SXT, TRX | 6 Cyl 6.7 L DIESEL, 8 Cyl 5.7 L GAS
- Ram 3500 | 2010 | Laramie, SLT, ST | 6 Cyl 6.7 L DIESEL
View related parts
Dodge Fuel Pump, Driver Side Part Number: 5145583AD
$497.25 MSRP: $750.00
You Save: $252.75 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Fuel Pump/Level Unit; Electric Fuel Pump Assembly; Fuel Level Sensor; Sending Unit.; Fuel Gauge Sending Unit; Fuel Pump Assembly
- Position: Driver Side
- Replaced by: 5145583AE
- Replaces: 5145583AB, 5145583AA, RL145583AB, 5145583AC
Fits the following Dodge Models:
- Durango | 2011-2015 | Citadel, Crew, Limited, R/T, Special Service | 8 Cyl 5.7 L GAS
View related parts
Dodge Fuel Pump Part Number: 68237949AA
$602.27 MSRP: $877.00
You Save: $274.73 (32%)
ADD TO CART
Product Specifications
- Other Name: Module - Fuel Pump/Level Unit; Fuel Pump and Sender Assembly; Fuel Sending Unit; Module Kit Fuel Pump/Level Unit
Fits the following Dodge Models:
- Dart | 2013-2016 | Aero, GT, Limited, R/T, Rallye, SE, SXT, SXT Sport | 4 Cyl 1.4 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Fuel Gauge Sending Unit Part Number: 4897497AA
$115.67 MSRP: $174.00
You Save: $58.33 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Level Unit - Fuel; Fuel Sender and Hanger Assembly; Fuel Level Sensor; Fuel Sending Unit; Sending Unit; Level Unit Kit Fuel
Fits the following Dodge Models:
- B1500 | 1996 | Base | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS
- B2500 | 1996 | Base | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- B3500 | 1996 | Base | 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- Ram 1500 | 1994-1997 | Base, LT, Laramie, SS/T 5.9L, ST, Sport, WS | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- Ram 2500 | 1994-1997 | Base | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- Ram 3500 | 1994-1997 | Base | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
View More
View related parts
Dodge Fuel Gauge Sending Unit Part Number: 68145782AA
$81.97 MSRP: $183.00
You Save: $101.03 (56%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Level Unit; Fuel Sender and Hanger Assembly; Fuel Transfer Unit; Fuel Level Sensor; Level Sensor; Module Kit Level Unit
Fits the following Dodge Models:
- Challenger | 2011-2019 | 392 Hemi Scat Pack Shaker, GT, R/T, R/T 392, R/T Classic, R/T Plus, R/T Plus Shaker, R/T Scat Pack, R/T Scat Pack Widebody, R/T Shaker, Rallye Redline, SE, SRT 392, SRT8, SXT, SXT Plus, Scat Pack, T/A, T/A 392 | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
- Charger | 2011-2019 | Daytona, Daytona 392, GT, GT Plus, Pursuit, R/T, R/T 392, R/T Road & Track, R/T Scat Pack, SE, SRT 392, SRT Hellcat, SRT8, SXT, SXT Plus, SXT Plus Leather, Scat Pack | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Fuel Gauge Sending Unit Part Number: 68000605AC
$109.28 MSRP: $163.00
You Save: $53.72 (33%)
ADD TO CART
Product Specifications
- Other Name: Module - Level Unit; Fuel Sender and Hanger Assembly; Fuel Level Sensor; Level Sensor; Module Kit Level Unit
- Replaces: 68000605AA, 68000605AB
Fits the following Dodge Models:
- Challenger | 2011-2019 | 392 Hemi Scat Pack Shaker, GT, R/T, R/T 392, R/T Classic, R/T Plus, R/T Plus Shaker, R/T Scat Pack, R/T Scat Pack Widebody, R/T Shaker, Rallye Redline, SE, SRT 392, SRT8, SXT, SXT Plus, Scat Pack, T/A, T/A 392 | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
- Charger | 2011-2019 | Daytona, Daytona 392, GT, GT Plus, Pursuit, R/T, R/T 392, R/T Road & Track, R/T Scat Pack, SE, SRT 392, SRT Hellcat, SRT8, SXT, SXT Plus, SXT Plus Leather, Scat Pack | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Fuel Pump Part Number: 68166594AC
$391.17 MSRP: $590.00
You Save: $198.83 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Fuel Pump/Level Unit; Fuel Pump Assembly; Fuel Sending Unit.; Module Kit Fuel Pump/Level Unit
- Replaces: 68166594AA, 68166594AB
Fits the following Dodge Models:
- Dart | 2012-2016 | Aero, GT, Limited, R/T, Rallye, SE, SXT, SXT Sport | 1.4L L4, 2.0L L4, 2.4L L4, 4 Cyl 1.4 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Fuel Pump Part Number: 68004936AE
$450.91 MSRP: $640.00
You Save: $189.09 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Fuel Pump/Level Unit; Fuel Sender Assembly; Electric Fuel Pump; Fuel Level Sensor.; Fuel Gauge Sending Unit; Sending Unit
- Replaces: 68017714AC, 68004936AB, 68004936AC, 68004936AD, RL004936AC
Fits the following Dodge Models:
- Avenger | 2008-2011 | Express, Heat, Lux, Mainstreet, SE, SXT | 2.4L L4, 2.7L V6, 3.5L V6, 6 Cyl 2.7 L FLEX, 6 Cyl 3.6 L FLEX
- Nitro | 2007-2011 | Detonator, Heat, R/T, SE, SLT, SXT, Shock | 3.7L V6, 4.0L V6, 6 Cyl 3.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
Dodge Fuel Pump Part Number: 68050948AB
$510.67 MSRP: $747.00
You Save: $236.33 (32%)
ADD TO CART
Product Specifications
- Other Name: Module - Fuel Pump/Level Unit; Electric Fuel Pump Assembly; Fuel Level Sensor; Sending Unit.; Fuel Pump Assembly; Level Sensor
- Replaces: 5145594AA, RL050948AA, 68050948AA, RL145594AA
Fits the following Dodge Models:
- Ram 1500 | 2009-2010 | Laramie, SLT, ST, Sport, TRX, TRX4 | 3.7L V6, 4.7L V8, 5.7L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
Dodge Fuel Pump Part Number: 68026581AD
$1823.25 MSRP: $2750.00
You Save: $926.75 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Kit - Fuel Pump/Level Unit; Fuel Pump and Strainer Set; Electric Fuel Pump; Fuel Sending Unit; Module Kit Fuel Pump/Level Unit
- Replaces: 68026581AA, 68026581AC, 68026581AB
Fits the following Dodge Models:
- Viper | 2015-2017, 2013, 2008-2010 | ACR, Base, GT, GTC, GTS, SRT-10, SRT-10 ACR | 10 Cyl 8.4 L GAS, 8.4L V10
View related parts
Dodge Fuel Gauge Sending Unit Part Number: 68037306AA
$60.86 MSRP: $87.25
You Save: $26.39 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Level Unit - Fuel; Level Indicator; Level Unit Kit Fuel
Fits the following Dodge Models:
- Dakota | 2008-2009 | Big Horn, Laramie, Lone Star, SLT, ST, SXT, Sport, TRX, TRX4 | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX
View related parts
Dodge Fuel Pump Part Number: 68237937AA
$508.38 MSRP: $740.00
You Save: $231.62 (32%)
ADD TO CART
Product Specifications
- Other Name: Module - Fuel Pump/Level Unit; Fuel Pump and Sender Assembly; Fuel Pump Module Assembly; Fuel Sending Unit; Module Kit Fuel Pump/Level Unit
- Replaced by: 68237937AB
Fits the following Dodge Models:
- Dart | 2014-2016 | Aero, GT, Limited, SE, SXT, SXT Sport | 4 Cyl 1.4 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Fuel Gauge Sending Unit Part Number: 5014353AA
$78.31 MSRP: $99.27
You Save: $20.96 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Level Kit - Fuel; Fuel Sender and Hanger Assembly; Fuel Level Sensor; Fuel Sending Unit; Sending Unit; Level Unit Kit Fuel
Fits the following Dodge Models:
- Neon | 2000-2005 | ACR, Base, ES, High Line, R/T, SE, SRT-4, SXT | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Fuel Pump Part Number: 4798671
$1054.63 MSRP: $1336.93
You Save: $282.30 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Level Unit; Fuel Pump Assembly; Strainers & Port; Reservoir; Level Sensor; Sending Unit; Fuel Gauge Sending Unit; Fuel Pump Assembly; Module, Fuel Pump And Level Unit; Module Kit Level Unit
Fits the following Dodge Models:
- Ram 2500 | 1996-1997 | Base | 6 Cyl 5.9 L DIESEL
- Ram 3500 | 1996-1997 | Base | 6 Cyl 5.9 L DIESEL
View related parts
Dodge Fuel Gauge Sending Unit Part Number: 68027708AA
$216.40 MSRP: $265.00
You Save: $48.60 (19%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Level Kit - Fuel; Fuel Sender and Hanger Assembly; Fuel Tank Sending Unit; Fuel Level Sensor; Level Sensor; Level Unit Kit Fuel
Fits the following Dodge Models:
- Viper | 2015-2017, 2008-2010 | ACR, Base, GT, GTC, GTS, SRT-10, SRT-10 ACR | 10 Cyl 8.4 L GAS
View related parts
Dodge Fuel Pump Part Number: 68367539AA
$361.34 MSRP: $548.00
You Save: $186.66 (35%)
ADD TO CART
Product Specifications
- Other Name: Module - Fuel Pump/Level Unit; Fuel Pump Assembly; Fuel Sending Unit.; Fuel Pump/Level Unit Kit: Fuel Pump Module, Sending Unit, O-Ring.
Fits the following Dodge Models:
- Charger | 2017-2019 | Daytona, Pursuit, R/T, SE, SXT | 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS
View related parts
Dodge Fuel Gauge Sending Unit Part Number: 68258754AA
Product Specifications
- Other Name: Module - Level Unit; Fuel Level Sensor; Module Kit Level Unit
Fits the following Dodge Models:
- Challenger | 2015-2019 | SRT Demon, SRT Hellcat, SRT Hellcat Redeye, SRT Hellcat Redeye Widebody, SRT Hellcat Widebody | 8 Cyl 6.2 L GAS
View related parts
Dodge Fuel Pump, Passenger Side Part Number: 5136023AF
$313.84 MSRP: $467.00
You Save: $153.16 (33%)
Product Specifications
- Other Name: Module Kit - Pickup/Level Unit; Fuel Pump and Sender Assembly, Right; Fuel Transfer Unit; Fuel Level Sensor; Fuel Gauge Sending Unit; Module Kit includes Pickup, Sending Unit, Level Unit, and O-Ring.
- Position: Passenger Side
- Replaces: 5136023AB, RL136023AD, RL136023AC, 5136023AD, 5136023AE, 5136023AC
Fits the following Dodge Models:
- Challenger | 2008-2023 | 392 Hemi Scat Pack Shaker, GT, R/T, R/T 392, R/T Classic, R/T Plus, R/T Plus Shaker, R/T Scat Pack, R/T Scat Pack Shaker Widebody, R/T Scat Pack Widebody, R/T Shaker, Rallye Redline, SE, SRT 392, SRT8, SXT, SXT Plus, Scat Pack, T/A, T/A 392, T/A 392 Widebody | 3.5L V6, 3.6L V6, 5.7L V8, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.1L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS, 8 Cyl 6.4 L GAS
- Charger | 2006-2023 | Base, Daytona, Daytona 392, Daytona R/T, GT, GT Plus, Pursuit, R/T, R/T 392, R/T Road & Track, R/T Scat Pack, SE, SRT 392, SRT Hellcat, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT8, SXT, SXT Plus, SXT Plus Leather, Scat Pack, Scat Pack 392 Widebody, Scat Pack Widebody | 2.7L V6, 3.5L V6, 3.6L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.1L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
- Magnum | 2005-2008 | R/T, SE, SRT8, SXT, SXT Special Edition | 2.7L V6, 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6.1L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View More
View related parts
Dodge Fuel Pump Part Number: 68258756AD
$516.40 MSRP: $754.00
You Save: $237.60 (32%)
Product Specifications
- Other Name: Module Kit - Pickup/Level Unit; Fuel Pump and Sender Assembly; Fuel Level Sensor; Fuel Sending Unit; Fuel Gauge Sending Unit; Module Kit includes Pickup, Level Unit, and O-Ring.
- Replaces: 68258756AB, 68258756AA, 68258756AC
Fits the following Dodge Models:
- Challenger | 2015-2023 | SRT Demon, SRT Demon 170, SRT Hellcat, SRT Hellcat Jailbreak, SRT Hellcat Redeye, SRT Hellcat Redeye Jailbreak, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT Super Stock | 6.2L V8, 8 Cyl 6.2 L GAS
- Charger | 2015-2021 | SRT Hellcat, SRT Hellcat Redeye Widebody, SRT Hellcat Widebody | 6.2L V8, 8 Cyl 6.2 L GAS

| Page 1 of 8 |Next >

1-20 of 145 Results

Dodge Fuel Level Sensor

OEM parts sourced directly from Dodge deliver superior quality, long lasting strength, and a precise fit you can trust. Each item goes through strict quality checks to ensure safety, toughness, and performance that matches your factory equipment. At JeepPartsDeal online shop, you'll get top-quality, budget-friendly OEM Dodge Fuel Level Sensor for your vehicle. We focus on giving you a high standard without pushing up the price. Our full selection of genuine factory products comes backed by the original manufacturer's warranty. You'll love our fast delivery, seamless shopping experience, and convenient return policy, saving you all the hassle.

Dodge Fuel Level Sensor Parts and Q&A

Fuel Pump Gasket
68304753AA
Q: How to Service and Repair the Fuel Level Sensor on the Left Side Module on Dodge Charger?
A:
Before working on the left side module's fuel level sensor, you must loosen the fuel pressure and remove the negative battery cable. Make sure not to let the fuel go higher than 5/8 of the tank's capacity before removing the module lock-ring. Loop a 30-inch long nylon tube with a 30-degree cut over the check valve on the tank to drain only part of the fuel. Take off the backmost lower seat cushion by pushing it back and lifting it all the way up and then fold the foam pad above the access cover for the modules back as well. Take the electrical connector off the left side module and mark how it should be placed. Loosen the left side module lock ring using special tool #9340 and then push the hose into the fuel tank from above to empty the left side fuel. Release the electrical connectors of both side fuel level sensors and lift off the top half of the module to tilt the bottom half and remove any remaining fuel. Pull the wire out of the sensor module and use a screwdriver to lift the level sensor straight up and remove it from the module. Reinstall the level sensor with the locking tabs secure, route the wires where they belong and mount the module top on top of the bottom. Secure the electrical connections from the right fuel level sensor, the left module sensor and the fuel pump and use the marks to ensure the module is facing correctly as you secure it with special tool #9340. Reattach the left side electrical connector, place the plastic access cover over it and next, fold the seat pad back and insert the lower seat cushion at the back. Fill the tank with fuel, hook the negative battery cable back up and scan the car while pushing the pressure on the fuel system to look for specific problems.
Fuel Gauge Sending Unit
5072766AD
Q: How to Remove and Install a Fuel Level Sensor from the Fuel Pump Module on Dodge Ram 1500?
A:
Both the fuel level sending unit and the float assembly are part of the fuel pump module and can be found on its side. First, take out the fuel pump module before removing the fuel level sensor from the fuel tank. Then, holding the plastic tab in an open position, slowly slide the assembly to the back to separate the sending unit from the pump module. Undo the 4-wire connector from the fuel pump module and pull out the wires needed from this connector using a terminal pick/removal tool. To install the mixer, join the wire connections to the electrical connectors and put the 4-wire electrical connector onto the pump module. Step 2: Place the sending unit above the pump, slide and snap it and then connect the fuel pump module.