How to Service an ABS Control Module on Chrysler 300?

For Electronic Brake Control Module servicing, the negative battery cable should be removed from the battery post first and then isolated. Following this, unplug the 47-Way wiring connector found at the ABM. Release the brake tubes from the two clips above the upper radiator support and unclip the brake tube from the clip under the Fuse And Relay Center. Grasp the whole assembly at the mounting grommets and pull it slightly to the center to access the attaching screws of the ABM, without pinching the brake tubes. Lift off the ABM from the HCU using three screws, then take them off the HCU. Put the solenoids and pump/motor line from the ABM into the HCU's valve connector passage, then align the opposite ends of the ABM with the valve and insert it onto the HCU. Place the three screws in the ABM and use a torque wrench to fasten them to the HCU with 2 N.m. Place the assembly so that it sits above the mounting grommets and then press the bracket down to attach it. Cut and clip the brake tube beneath the Fuse And Relay Center and clip the second brake tube to a routing clip by the upper radiator support. Connect the 47-way wiring connector at the ABM and get the negative battery cable attached tightly at the battery post. Perform the last test, Diagnostic Verification and correct any existing problems.

How to Service and Repair an ABS Control Module on Chrysler Crossfire?

To start work on the Electronic Brake Control Module, turn off the negative battery cable and clean the top of the Hydraulic Control Unit (HCU) nearby the hydraulic lines. Before removing the hydraulic lines, mark them and the connected ports so you don't get confused and then close them with plugs so they don't leak. Remove the Connector Antilock Brake (CAB) cable from its port and take off the retaining bracket from the Integrated Control Unit (ICU). While gently pulling the ICU, side the hydraulic lines and unscrew the CAB from the HCU. The CAB should be joined with the HCU using screws after checking and changing the ICU rubber grommets if necessary. Fit the ICU onto the retaining bracket by using screws, while tracing the hoses to the corresponding wheel if you need to. Attach the brake lines (1-6) at the proper marks, connect the CAB harness connector and next connect the negative battery cable. After that, bleed the brakes and clear the fault codes from the system's memory.

OEM Chrysler ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

164 ABS Control Modules found

View related parts
Chrysler Modulator Valve Part Number: 68258639AA
$598.91 MSRP: $907.00
You Save: $308.09 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator - Anti-Lock Brake; ABS Control Module; ABS Control Unit; Modulator; Hydraulic Control Unit Anti-Lock Brake System; Control Unit Anti-Lock Brake
Fits the following Chrysler Models:
- 300 | 2015-2023 | C, C Platinum, Limited, S, Touring, Touring L | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Chrysler Control Module Part Number: 68435852AF
$182.41 MSRP: $272.00
You Save: $89.59 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Anti-Lock Brake System
- Replaces: 68435852AB, 68435852AC, 68435852AA, 68435852AE, 68435852AD
Fits the following Chrysler Models:
- 300 | 2019-2023 | C, Limited, S, Touring, Touring L | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Chrysler Modulator Valve Part Number: 68210116AA
Product Specifications
- Other Name: Master Cylinder - Anti-Lock Brake System; ABS Hydraulic Assembly; ABS Modulator Valve; ABS Control Module; Modulator; Hydraulic Control Unit Anti-Lock Brake System
Fits the following Chrysler Models:
- 300 | 2013-2014 | Base, C, C Luxury, S, SRT8, SRT8 Core | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Chrysler Control Module Part Number: 5175609AE
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module
- Replaces: 5175609AA, 5175609AC, 5175609AD, 5175609AB
Fits the following Chrysler Models:
- 300 | 2006 | Base, C, C SRT8, Limited, Touring | 2.7L V6, 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6.1L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Chrysler Control Module Part Number: 68210120AB
Product Specifications
- Other Name: Module - Anti-Lock Brake; ABS Hydraulic Assembly; ABS Control Module; Modulator Valve; ABS Control Unit; Includes Items 1, 3, 4, 7.
- Replaces: 68195728AA, 68210120AA
Fits the following Chrysler Models:
- 300 | 2013-2014 | Base, C, C Luxury, S, SRT8, SRT8 Core | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Chrysler Control Module Part Number: 68087355AA
Product Specifications
- Other Name: Module - Anti-Lock Brake; ABS Hydraulic Assembly; ABS Control Module; Modulator Valve; ABS Control Unit; Control Unit Anti-Lock Brake
Fits the following Chrysler Models:
- 300 | 2011 | Base, C, Limited | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS
View related parts
Chrysler Modulator Valve Part Number: 5018254AA
Product Specifications
- Other Name: Accumulator - Anti-Lock Brake System; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit; Modulator; Hydraulic Control Unit Anti-Lock Brake System
Fits the following Chrysler Models:
- Sebring | 2001-2004 | Base, GTC, LX, LXi, Limited, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
Chrysler ABS Control Unit Part Number: 5096213AA
Product Specifications
- Other Name: Control - Anti-Lock Brake; ABS Control Module; Control Unit Anti-Lock Brake
Fits the following Chrysler Models:
- Sebring | 2003-2004 | Base, GTC, LX, LXi, Limited, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Chrysler Control Module Part Number: 5102525AA
Product Specifications
- Other Name: Control - Anti-Lock Brake; ABS Control Module; ABS Control Unit; Control Unit Anti-Lock Brake
Fits the following Chrysler Models:
- Sebring | 2003-2004 | Base, GTC, LX, LXi, Limited, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
Chrysler ABS Control Unit Part Number: 5102526AA
Product Specifications
- Other Name: Accumulator - Anti-Lock Brake System; ABS Hydraulic Assembly; ABS Control Module; Modulator; Hydraulic Control Unit Anti-Lock Brake System
Fits the following Chrysler Models:
- Sebring | 2004 | Base, LX, LXi, Limited, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
Chrysler Control Module Part Number: 5134112AA
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module; Module Anti-Lock Brake System
Fits the following Chrysler Models:
- 300 | 2005 | Base, C, C SRT8, Limited, Touring | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Chrysler Control Module Part Number: 5134113AA
Product Specifications
- Other Name: Master Cylinder - Anti-Lock Brake System; ABS Modulator Valve; ABS Control Module; Modulator Valve; Modulator; Hydraulic Control Unit Anti-Lock Brake System
Fits the following Chrysler Models:
- 300 | 2005-2007 | Base, C, C SRT8, Limited, Touring | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Chrysler Modulator Part Number: 5142277AA
Product Specifications
- Other Name: Accumulator - Anti-Lock Brake System; ABS Modulator Valve; ABS Control Module; Hydraulic Control Unit Anti-Lock Brake System
Fits the following Chrysler Models:
- Pacifica | 2005-2006 | Base, Limited, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Modulator Part Number: 5142280AA
Product Specifications
- Other Name: Accumulator - Anti-Lock Brake System; ABS Modulator Valve; ABS Control Module; Hydraulic Control Unit Anti-Lock Brake System
Fits the following Chrysler Models:
- Pacifica | 2005-2006 | Base, Limited, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Control Module Part Number: 5142282AA
Product Specifications
- Other Name: Control - Anti-Lock Brakes; ABS Control Module; Module Anti-Lock Brakes
Fits the following Chrysler Models:
- Pacifica | 2005-2006 | Base, Limited, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Control Module Part Number: 5159191AA
Product Specifications
- Other Name: Control - Anti-Lock Brakes; ABS Control Module; ABS Control Unit; Module Anti-Lock Brakes
Fits the following Chrysler Models:
- Sebring | 2005 | Base, GTC, Limited, TSi, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Chrysler Control Module Part Number: 5159191AB
Product Specifications
- Other Name: Control - Anti-Lock Brakes; ABS Control Module; ABS Control Unit; Module Anti-Lock Brakes
Fits the following Chrysler Models:
- Sebring | 2006 | Base, GTC, Limited, TSi, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Chrysler Control Module Part Number: 5170344AA
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module; Module Anti-Lock Brake System
Fits the following Chrysler Models:
- 300 | 2005 | Base, C, C SRT8, Limited, Touring | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Chrysler Control Module Part Number: 68028992AA
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module; Module Anti-Lock Brake System
Fits the following Chrysler Models:
- 300 | 2008 | C, C SRT8, LX, Limited, Touring | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Chrysler Modulator Part Number: 68037140AA
Product Specifications
- Other Name: Control - Anti-Lock Brake; ABS Modulator Valve; ABS Control Module; Control Unit Anti-Lock Brake
Fits the following Chrysler Models:
- 300 | 2008 | C, C SRT8, LX, Limited, Touring | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS

| Page 1 of 9 |Next >

1-20 of 164 Results

Chrysler ABS Control Module

OEM parts sourced directly from Chrysler deliver superior quality, long lasting strength, and a precise fit you can trust. Each item goes through strict quality checks to ensure safety, toughness, and performance that matches your factory equipment. At JeepPartsDeal online shop, you'll get top-quality, budget-friendly OEM Chrysler ABS Control Module for your vehicle. We focus on giving you a high standard without pushing up the price. Our full selection of genuine factory products comes backed by the original manufacturer's warranty. You'll love our fast delivery, seamless shopping experience, and convenient return policy, saving you all the hassle.

Chrysler ABS Control Module keeps wheels turning under hard stops, guarding control when panic strikes. Ever since 1925, Chrysler has prolonged firm construction, reasonable cost, and an aptitude for original concepts that have made traveling in a vehicle less of a burden for anyone on the steering wheel. Chrysler made the shake of engines disappear with Floating Power, reduced wind drag by bold Airflow lines, and kept cabins serene over broken pavement and unpaved roads. Families applauded when Chrysler unveiled the first viable minivan, its sliding doors, level base, and sincere room that made grocery runs hassle-free cruises. Even now Chrysler continues to dial interior stretch-out space, cloud-like ride, and straightforward controls that do not flaunt about with your time but respect it. ABS Control Module continuously measures the speed of four wheels in real time and compares rotational data hundreds of times a second to warn of danger in advance. A quick solenoid valve assembly and a small pump allowed the ABS Control Module to either depress or increase brake pressure without making the solenoid pulse or the pedal flutter. The ABS Control Module, linked to the brain of the car, stops lock-ups halfway around the corner to allow the car to cling to the surface, the steering to react, and the skids in the rainy season to remain an exception. The ABS Control Module has Electronic Brakeforce Distribution, which redistributes stop power between the front and rear to reduce distance with passengers crowding in or luggage crammed in the trunk.

Chrysler ABS Control Module Parts and Q&A

Control Module
5134114AA
Q: How to Service an ABS Control Module on Chrysler 300?
A:
For Electronic Brake Control Module servicing, the negative battery cable should be removed from the battery post first and then isolated. Following this, unplug the 47-Way wiring connector found at the ABM. Release the brake tubes from the two clips above the upper radiator support and unclip the brake tube from the clip under the Fuse And Relay Center. Grasp the whole assembly at the mounting grommets and pull it slightly to the center to access the attaching screws of the ABM, without pinching the brake tubes. Lift off the ABM from the HCU using three screws, then take them off the HCU. Put the solenoids and pump/motor line from the ABM into the HCU's valve connector passage, then align the opposite ends of the ABM with the valve and insert it onto the HCU. Place the three screws in the ABM and use a torque wrench to fasten them to the HCU with 2 N.m. Place the assembly so that it sits above the mounting grommets and then press the bracket down to attach it. Cut and clip the brake tube beneath the Fuse And Relay Center and clip the second brake tube to a routing clip by the upper radiator support. Connect the 47-way wiring connector at the ABM and get the negative battery cable attached tightly at the battery post. Perform the last test, Diagnostic Verification and correct any existing problems.
Control Module
5140827AB
Q: How to Service and Repair an ABS Control Module on Chrysler Crossfire?
A:
To start work on the Electronic Brake Control Module, turn off the negative battery cable and clean the top of the Hydraulic Control Unit (HCU) nearby the hydraulic lines. Before removing the hydraulic lines, mark them and the connected ports so you don't get confused and then close them with plugs so they don't leak. Remove the Connector Antilock Brake (CAB) cable from its port and take off the retaining bracket from the Integrated Control Unit (ICU). While gently pulling the ICU, side the hydraulic lines and unscrew the CAB from the HCU. The CAB should be joined with the HCU using screws after checking and changing the ICU rubber grommets if necessary. Fit the ICU onto the retaining bracket by using screws, while tracing the hoses to the corresponding wheel if you need to. Attach the brake lines (1-6) at the proper marks, connect the CAB harness connector and next connect the negative battery cable. After that, bleed the brakes and clear the fault codes from the system's memory.