How to Install a Brake Master Cylinder on Dodge Challenger?

Before installing the Brake Master Cylinder, completely bleed the master cylinder after removal. A vacuum seal should be put on the master cylinder when replacing the brake fluid. Put the new vacuum seal on the rear section of the master cylinder and make sure it is straight in the groove. Position the master cylinder over the studs, so that the booster push rod fits into the master cylinder piston. Place and tighten the two master cylinder mounting nuts to 15 Nm (133 in. lbs.). Place the primary and secondary brake tubes into the primary and secondary openings on the master cylinder, then tighten each one to 20 Nm (177 in. lbs.). Connect the wiring harness connector to the brake fluid level sensor which is placed in the brake fluid reservoir. Connect the cable marked "negative" from your battery charger to the battery post. Add only clean, fresh Mopar(R) Brake Fluid or an equivalent brake fluid into the master cylinder fluid reservoir. Insert the access panel inside the cowl of the airplane. Operation of the vehicle should not be attempted until the brake pedal is firm; if it is not, bleed the brake system and carefully inspect for leaks. Do a last road test to confirm the brakes are functioning as they should.

How to Remove and Replace a Brake Master Cylinder on Dodge Charger?

You need to take off the access panel in the cowl area first in order to see and remove the brake master cylinder. Wipe all surfaces in the brake fluid reservoir and master cylinder using Mopar(R) Brake Parts Cleaner or an equivalent cleaner. Take out the wiring harness connector from the brake fluid level sensor in the master cylinder brake fluid reservoir. Open the cover on the brake fluid reservoir and, with a clean syringe or similar instrument, drain as much brake fluid as you can. Don't use any tool to remove the fluid reservoir from the master cylinder, because this could damage either the reservoir or the housing. After that, remove the screw holding the fluid reservoir to the master cylinder housing. Pull up on the brake pedal as you shake the brake fluid reservoir from side to side, so as to remove it from its seal grommets in the master cylinder. Leave the reservoir doors open and then remove the seals covering the reservoir access openings on the master cylinder housing.

OEM Dodge Brake Master Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

100 Brake Master Cylinders found

View related parts
Dodge Master Cylinder Part Number: 68207364AA
$197.36 MSRP: $295.00
You Save: $97.64 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder - Brake; Brake Master Cylinder Reservoir; Brake Master Cylinder; Brake Reservoir; Master Cylinder Reservoir; Reservoir; Master Cylinder Brake
- Replaces: 4560183AA, 4560184AA
Fits the following Dodge Models:
- Durango | 2011-2015 | Citadel, Crew, Express, Heat, Limited, R/T, Rallye, Special Service, SXT | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS
View related parts
Dodge Master Cylinder Part Number: 68166817AA
$91.08 MSRP: $201.00
You Save: $109.92 (55%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
Fits the following Dodge Models:
- Dart | 2013-2014 | Aero, GT, Limited, R/T, Rallye, SE, SXT | 4 Cyl 1.4 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Master Cylinder Part Number: 68192625AA
$103.28 MSRP: $226.00
You Save: $122.72 (55%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder - Brake; Brake Master Cylinder; Clutch Master Cylinder; Master Cylinder Brake
Fits the following Dodge Models:
- Dart | 2013-2016 | Aero, GT, Limited, R/T, Rallye, SE, SXT, SXT Sport | 4 Cyl 1.4 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Master Cylinder Part Number: 5175103AA
$138.26 MSRP: $209.00
You Save: $70.74 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
Fits the following Dodge Models:
- Dakota | 2006-2010 | Big Horn, Laramie, Lone Star, SLT, ST, SXT, Sport, TRX, TRX4 | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
Dodge Master Cylinder Part Number: 68192615AA
$162.79 MSRP: $243.00
You Save: $80.21 (34%)
ADD TO CART
Product Specifications
- Other Name: Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
Fits the following Dodge Models:
- Dart | 2013-2016 | Aero, GT, Limited, R/T, Rallye, SE, SXT, SXT Sport | 4 Cyl 1.4 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Master Cylinder Part Number: 68155423AD
$245.31 MSRP: $371.00
You Save: $125.69 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Replaces: 68155423AB, 68155423AC, 68155423AA
Fits the following Dodge Models:
- Journey | 2012-2020 | AVP, Crossroad, GT, Limited, R/T, SE, SE Value, SXT | 2.4L L4, 3.6L V6, 4 Cyl 2.4 L GAS, 6 Cyl 3.6 L FLEX
View related parts
Dodge Master Cylinder Part Number: 4581491AD
$211.85 MSRP: $316.00
You Save: $104.15 (33%)
ADD TO CART
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Replaces: 4581491AC, 4581491AB, 4581491AA
Fits the following Dodge Models:
- Grand Caravan | 2012-2020 | American Value Package, Crew, GT, R/T, SE, SE 30th Anniversary Edition, SE Plus, SXT, SXT 30th Anniversary Edition | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Dodge Master Cylinder Part Number: 5189174AA
$217.37 MSRP: $275.56
You Save: $58.19 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
Fits the following Dodge Models:
- Magnum | 2007 | SRT8 | 8 Cyl 6.1 L GAS
View related parts
Dodge Master Cylinder Part Number: 5119355AA
$331.34 MSRP: $420.03
You Save: $88.69 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder - Brake Master; Brake Master Cylinder; Cylinder Brake Master
Fits the following Dodge Models:
- Sprinter 2500 | 2003-2006 | Base | 5 Cyl 2.7 L DIESEL
- Sprinter 3500 | 2003-2006 | Base | 5 Cyl 2.7 L DIESEL
View related parts
Dodge Master Cylinder Part Number: 68193548AA
$257.19 MSRP: $313.00
You Save: $55.81 (18%)
ADD TO CART
Product Specifications
- Other Name: Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
Fits the following Dodge Models:
- Viper | 2015-2017 | ACR, Base, GT, GTC, GTS | 10 Cyl 8.4 L GAS
View related parts
Dodge Master Cylinder Part Number: 5189175AA
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
Fits the following Dodge Models:
- Magnum | 2007 | R/T, SE, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS
View related parts
Dodge Master Cylinder Part Number: 5011256AB
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
Fits the following Dodge Models:
- Ram 1500 | 1998-2001 | Laramie, SLT, SS/T 5.9L, ST, Sport, WS | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- Ram 2500 | 1998-2000 | Base | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
- Ram 3500 | 1998-2000 | Base | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
View More
View related parts
Dodge Master Cylinder Part Number: 5142652AA
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
Fits the following Dodge Models:
- Dakota | 2005 | Laramie, SLT, ST, Sport | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L GAS
View related parts
Dodge Master Cylinder Part Number: 5102032AA
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
Fits the following Dodge Models:
- Ram 1500 | 2003-2005 | Laramie, SLT, SRT-10, ST | 10 Cyl 8.3 L GAS, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.9 L GAS
View related parts
Dodge Master Cylinder Part Number: 4779168AB
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
Fits the following Dodge Models:
- Intrepid | 2001-2004 | ES, Police, R/T, SE, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.2 L GAS, 6 Cyl 3.5 L GAS
View related parts
Dodge Master Cylinder Part Number: 4695192
Product Specifications
- Other Name: Master Cylinder W/ABS Tc; Master Cylinder Assembly, W/O ABS; Master Cylinder Brake
Fits the following Dodge Models:
- Intrepid | 1995-1997 | Base, ES | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L GAS
View related parts
Dodge Master Cylinder Part Number: 4683264AD
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
Fits the following Dodge Models:
- Caravan | 2001-2007 | Base, C/V, Ec, SE, SXT, Sport | 4 Cyl 2.4 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
- Grand Caravan | 2001-2007 | Anniversary Edition, Base, C/V, EL, ES, EX, SE, SE Plus, SXT, Sport | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Dodge Master Cylinder Part Number: 4642548
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Assembly, Brake; Master Cylinder Brake
Fits the following Dodge Models:
- Viper | 1992-2000 | ACR, Base, GT2, GTS, R/T-10 | 10 Cyl 8.0 L GAS
View related parts
Dodge Master Cylinder Part Number: 4294946
Product Specifications
- Other Name: Brake Master Cylinder; Master Cylinder, Complete, W/O Fluid Window; Master Cylinder, Complete
Fits the following Dodge Models:
- Caravan | 1984-1995 | Base, C/V, ES, LE, SE | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 4 Cyl 2.6 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L CNG, 6 Cyl 3.3 L GAS
- Daytona | 1991-1993 | Base, ES, Iroc, Iroc R/T, Shelby | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
- Dynasty | 1989-1993 | Base, LE, LS | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS
- Grand Caravan | 1987-1995 | Base, ES, LE, SE | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
- Mini Ram | 1984-1988 | Base, Royal | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 4 Cyl 2.6 L GAS, 6 Cyl 3.0 L GAS
- Spirit | 1991-1993 | Base, ES, High Line, LE, R/T | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
View More
View related parts
Dodge Master Cylinder Reservoir Part Number: 5119356AA
Product Specifications
- Other Name: Master Cylinder - Brake Master Cylinder; Brake Master Cylinder Reservoir; Reservoir; Reservoir Brake Master Cylinder
Fits the following Dodge Models:
- Sprinter 2500 | 2003-2006 | Base | 5 Cyl 2.7 L DIESEL
- Sprinter 3500 | 2003-2006 | Base | 5 Cyl 2.7 L DIESEL

| Page 1 of 5 |Next >

1-20 of 100 Results

Dodge Brake Master Cylinder

OEM parts sourced directly from Dodge deliver superior quality, long lasting strength, and a precise fit you can trust. Each item goes through strict quality checks to ensure safety, toughness, and performance that matches your factory equipment. At JeepPartsDeal online shop, you'll get top-quality, budget-friendly OEM Dodge Brake Master Cylinder for your vehicle. We focus on giving you a high standard without pushing up the price. Our full selection of genuine factory products comes backed by the original manufacturer's warranty. You'll love our fast delivery, seamless shopping experience, and convenient return policy, saving you all the hassle.

Dodge Brake Master Cylinder converts light pressure of the pedal into assured stopping power enhancing safety within the entire lineup. Even in 1914, when the industry was tempted to use lightweight shortcuts, Dodge demonstrated that muscle could be applied without compromising durability or bold style, all-steel bodies. Dodge continued to play a game of gambling and introduced thunderous HEMI engines and the outrageous Viper program into dealerships so that an average driver could get a taste of racetrack rage on the regular roads. The same tuning was recently wired into the Fratzonic Chambered Exhaust, a 600-watt sound cannon which allows the electric cars to roar or whisper in accordance with the Drag, Donut, Sport, or Stealth mood. Dodge thus is a symbol of pure muscle with customization as each person is free to either select loud excitement or quiet cruise without watering down the tough essence or swagger of the brand. The Brake Master Cylinder is in the center of the hydro system, which transforms foot force into dual circuit pressure that prompts all calipers immediately. A diagonal split system with Brake Master Cylinder ensures that two opposite wheels remain alive in case one of the circuits is struck by a leak providing the fail-safe control that may mean the difference between a brush and a crash. Brake Master Cylinder is resistant to corrosion with rugged machining, thus its bores remain smooth and seals remain tight throughout the millions of miles. Brake Master Cylinder requires prompt visual inspection of fluid level and leakage since a drip can be solved before it fades, and that hard pedal drivers desire to have.

Dodge Brake Master Cylinder Parts and Q&A

Master Cylinder
68048551AC
Q: How to Install a Brake Master Cylinder on Dodge Challenger?
A:
Before installing the Brake Master Cylinder, completely bleed the master cylinder after removal. A vacuum seal should be put on the master cylinder when replacing the brake fluid. Put the new vacuum seal on the rear section of the master cylinder and make sure it is straight in the groove. Position the master cylinder over the studs, so that the booster push rod fits into the master cylinder piston. Place and tighten the two master cylinder mounting nuts to 15 Nm (133 in. lbs.). Place the primary and secondary brake tubes into the primary and secondary openings on the master cylinder, then tighten each one to 20 Nm (177 in. lbs.). Connect the wiring harness connector to the brake fluid level sensor which is placed in the brake fluid reservoir. Connect the cable marked "negative" from your battery charger to the battery post. Add only clean, fresh Mopar(R) Brake Fluid or an equivalent brake fluid into the master cylinder fluid reservoir. Insert the access panel inside the cowl of the airplane. Operation of the vehicle should not be attempted until the brake pedal is firm; if it is not, bleed the brake system and carefully inspect for leaks. Do a last road test to confirm the brakes are functioning as they should.
Master Cylinder
68033786AA
Q: How to Remove and Replace a Brake Master Cylinder on Dodge Charger?
A:
You need to take off the access panel in the cowl area first in order to see and remove the brake master cylinder. Wipe all surfaces in the brake fluid reservoir and master cylinder using Mopar(R) Brake Parts Cleaner or an equivalent cleaner. Take out the wiring harness connector from the brake fluid level sensor in the master cylinder brake fluid reservoir. Open the cover on the brake fluid reservoir and, with a clean syringe or similar instrument, drain as much brake fluid as you can. Don't use any tool to remove the fluid reservoir from the master cylinder, because this could damage either the reservoir or the housing. After that, remove the screw holding the fluid reservoir to the master cylinder housing. Pull up on the brake pedal as you shake the brake fluid reservoir from side to side, so as to remove it from its seal grommets in the master cylinder. Leave the reservoir doors open and then remove the seals covering the reservoir access openings on the master cylinder housing.