How to Replace a Wiper Switch on the Front Windshield on Jeep Wrangler?

You should stop air bag operation by taking out and isolating the battery negative cable and waiting two minutes. Remove the cover from the instrument panel above the steering column opening, then remove the two screws holding the lower steering column shroud to the upper one. When the vehicle has a tilt steering column, place the steering wheel flat and leave the release lever in the free position. Both shrouds on top and beneath the turn signal light should be removed and the multi-function switch cables joined to each receptacle should be disconnected from both sides. Take out two screws that join the multi-function switch assembly to the top of the steering column. Remove the assembly. Depress and remove two small screws that join the two multi-function switches and then pull the control handle on the right multi-function switch. When installing the switch, align the pins, place the right switch on the left switch and secure it by tightening the two screws to 2 Nm (20 in. lbs.). This time, position the switch assembly on the upper side of the column housing and mount it with two screws, tightened to 2 Nm (20 in. lbs.). Connect both cross body wire harness connectors to the switches and then attach the upper and lower shrouds to the steering column, making sure the tabs are in place. Screw the lower shroud to the upper shroud using two screws tightened to 2 Nm (18 in. lbs.). If the vehicle has a tilt steering column, raise it and position it, ensure it is locked, put back the cover over the opening and link up the negative battery cable.

How to Maintain a Wiper Switch for Rear Wipers and Washers on Jeep Wrangler?

Before servicing the wiper and washer switch, turn off the supplemental restraint system in vehicles with air bags by unplugging the vehicle's negative battery cable for two minutes. Take out the rear wiper and washer switch from the left side of the instrument panel's accessory switch bezel. Turn the control switch bulb holder counterclockwise with a small screwdriver about 30 degrees from the bottom, then remove the bulb holder and bulb unit. During installtion, select the proper bulb size and type to prevent the light from becoming too hot and being damaged. Set the bulb holder and bulb unit over the bulb mounting hole, push so it's firmly in place and twist the holder clockwise about 30 degrees. Put the rear wiper and washer switch back into place in the accessory switch bezel and connect the negative battery terminal.

OEM Jeep Wrangler Wiper Switch

Windshield Wiper Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

16 Wiper Switches found

View related parts
Jeep Wrangler Turn Signal Switch Part Number: 68015101AG
$89.70 MSRP: $135.00
You Save: $45.30 (34%)
ADD TO CART
Product Specifications
- Other Name: Switch - Multifunction; Turn Signal & Combination Lever; Steering Column Housing; Multi Purpose Switch; Multifunction Switch; Headlamp Switch; Switch Multifunction
- Replaces: 68015101AE, 68015101AD, 68015101AC, 68015101AF, 68015101AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2017 Jeep Wrangler | 70th Anniversary, 75th Anniversary, Rubicon, Sahara, Sport, Sport S, Unlimited 70th Anniversary, Unlimited 75th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited Sport S | 3.6L V6, 3.8L V6, 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS
View related parts
Jeep Wrangler Turn Signal Switch Part Number: 68041491AD
$121.54 MSRP: $184.00
You Save: $62.46 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Multifunction; Turn Signal & Combination Lever; Combination Switch; Multi Purpose Switch; Multifunction Switch; Switch Multifunction
- Replaces: 68024197AB, 68041491AB, 68041491AC, 68041491AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2017 Jeep Wrangler | 70th Anniversary, 75th Anniversary, Rubicon, Sahara, Sport, Sport S, Unlimited 70th Anniversary, Unlimited 75th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited Sport S | 3.6L V6, 3.8L V6, 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS
View related parts
Jeep Wrangler Wiper Switch Part Number: 68003215AD
$146.07 MSRP: $222.00
You Save: $75.93 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Wiper; Windshield Wiper Switch; Windshield Washer Switch; Front Wiper Switch; Switch Wiper
- Replaces: 68003215AC, 5183957AA, 68003215AB, 68003215AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2017 Jeep Wrangler | 70th Anniversary, 75th Anniversary, Rubicon, Sahara, Sport, Sport S, Unlimited 70th Anniversary, Unlimited 75th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited Sport S, Unlimited X, X | 3.8L V6, 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS
View related parts
Jeep Wrangler Rear Wiper Switch Part Number: 56000029
$26.43 MSRP: $33.51
You Save: $7.08 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Wiper; Switch, Rear Wiper
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1992-1995 Jeep Wrangler | Base, Islander, Renegade, Rio Grande, S, SE, Sahara | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Wrangler Turn Signal Switch Part Number: 68041485AD
$112.62 MSRP: $172.00
You Save: $59.38 (35%)
ADD TO CART
Product Specifications
- Other Name: Switch - Multifunction; Turn Signal & Combination Lever; Steering Column Housing; Multi Purpose Switch; Multifunction Switch; Headlamp Switch; Signal Switch; Switch Multifunction
- Replaces: 5183947AC, 68041485AA, 68041485AB, 5183947AA, 68041485AC, 5183947AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2017 Jeep Wrangler | 70th Anniversary, 75th Anniversary, Rubicon, Sahara, Sport, Sport S, Unlimited 70th Anniversary, Unlimited 75th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited Sport S, Unlimited X, X | 3.6L V6, 3.8L V6, 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS
View related parts
Jeep Wrangler Turn Signal Switch Part Number: 5183952AF
$44.94 MSRP: $66.60
You Save: $21.66 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Multifunction; Turn Signal & Combination Lever; Steering Column Housing; Multi Purpose Switch; Multifunction Switch; Headlamp Switch; Switch Multifunction
- Replaces: 5183952AA, 5183952AC, 5183952AB, 5183952AD, 5183952AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Jeep Wrangler | Rubicon, Sahara, Sport, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited X, X | 3.8L V6, 6 Cyl 3.8 L GAS
View related parts
Jeep Wrangler Turn Signal Switch Part Number: 5183950AF
Product Specifications
- Other Name: Switch - Multifunction; Steering Column Switch Housing; Combination Switch; Multi Purpose Switch; Multifunction Switch; Signal Switch; Switch Multifunction
- Replaces: 5183950AE, 5183950AD, 5183950AC, 5183950AB, 5183950AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Jeep Wrangler | Rubicon, Sahara, Sport, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited X, X | 3.8L V6, 6 Cyl 3.8 L GAS
View related parts
Jeep Wrangler Wiper Switch Part Number: 56007299
Product Specifications
- Other Name: Switch Assembly - Windshield Wiper/Washer - Intermittent; Windshield Washer Switch; Switch; Switch, Multi - Function Turn Signal & Wiper; Switch Assembly, Wipers
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1987-1995 Jeep Wrangler | Base, Islander, Laredo, Renegade, Rio Grande, S, SE, Sahara, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS, 6 Cyl 4.2 L GAS
View related parts
Jeep Wrangler Wiper Switch Part Number: 56007298
Product Specifications
- Other Name: Switch - Intermittent Wiper; Windshield Washer Switch; Front Wiper Switch; Multi-Function Turn Signal & Wiper Switch Assembly.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1987-1995 Jeep Wrangler | Base, Islander, Laredo, Renegade, Rio Grande, S, SE, Sahara, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS, 6 Cyl 4.2 L GAS
View related parts
Jeep Wrangler Rear Wiper Switch Part Number: 56007249
Product Specifications
- Other Name: Switch - Windshield Wiper; Back Glass Wiper Switch; Windshield Washer Switch; Front Wiper Switch; Switch; Switch Windshield Wiper
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2006 Jeep Wrangler | 65th Anniversary Edition, Rubicon, SE, Sahara, Sport, Unlimited, Unlimited Rubicon, X | 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Wrangler Wiper Switch Part Number: 4661942
Product Specifications
- Other Name: Switch, Wipers; Windshield Washer Switch; Front Wiper Switch; Switch, Wiper Control W/2 Speed Wipers; Switch Windshield Wiper; Switch, Wiper Control
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2000 Jeep Wrangler | SE, Sahara, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Wrangler Turn Signal Switch Part Number: 56010315AA
Product Specifications
- Other Name: Switch - Multifunction; Multi Purpose Switch; Signal Switch; Multifunction Left Stalk for Interior/Exterior Lights & Turn Signal Controls.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2001 Jeep Wrangler | SE, Sahara, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Wrangler Turn Signal Switch Part Number: 5183946AF
Product Specifications
- Other Name: Switch - Multifunction; Combination Switch; Multi Purpose Switch; Multifunction Switch; Signal Switch; Switch Multifunction
- Replaces: 5183946AA, 5183946AD, 5183946AE, 5183946AB, 5183946AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2017 Jeep Wrangler | 70th Anniversary, 75th Anniversary, Rubicon, Sahara, Sport, Sport S, Unlimited 70th Anniversary, Unlimited 75th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited Sport S, Unlimited X, X | 3.6L V6, 3.8L V6, 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS
View related parts
Jeep Wrangler Wiper Switch Part Number: 56000031
Product Specifications
- Other Name: Switch - Windshield Wiper; Windshield Washer Switch; Front Wiper Switch; Multi-Function Turn Signal & Wiper; Wiper Switch Assembly, W/O Intermittent.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1987-1995 Jeep Wrangler | Base, Islander, Laredo, Renegade, Rio Grande, S, SE, Sahara, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS, 6 Cyl 4.2 L GAS
View related parts
Jeep Wrangler Wiper Switch Part Number: 4793313
Product Specifications
- Other Name: Switch - Intermittent Wiper; Windshield Washer Switch; Front Wiper Switch; Intermittent Wiper Right Stalk with Washer & Wiper Functions.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2000 Jeep Wrangler | SE, Sahara, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Wrangler Wiper Switch Part Number: 5016711AB
Product Specifications
- Other Name: Switch - Intermittent Wiper; Windshield Washer Switch; Front Wiper Switch; Switch Intermittent Wiper Right Stalk Includes Windshield Washer & Wiper Functions
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2006 Jeep Wrangler | 65th Anniversary Edition, Rubicon, SE, Sahara, Sport, Unlimited, Unlimited Rubicon, X | 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS

Jeep Wrangler Wiper Switch

Choose OEM Wiper Switch that meet Jeep factory standards. Jeep designs and tests every component for precision and durability. Each Wiper Switch follows strict manufacturing steps to lock in quality and fit. If your Jeep Wrangler matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Wrangler parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Jeep Wrangler Wiper Switch Parts and Q&A

Wiper Switch
5016711AB
Q: How to Replace a Wiper Switch on the Front Windshield on Jeep Wrangler?
A:
You should stop air bag operation by taking out and isolating the battery negative cable and waiting two minutes. Remove the cover from the instrument panel above the Steering Column opening, then remove the two screws holding the lower steering column shroud to the upper one. When the vehicle has a tilt steering column, place the steering wheel flat and leave the release lever in the free position. Both shrouds on top and beneath the turn signal light should be removed and the multi-function switch cables joined to each receptacle should be disconnected from both sides. Take out two screws that join the multi-function switch assembly to the top of the steering column. Remove the assembly. Depress and remove two small screws that join the two multi-function switches and then pull the control handle on the right multi-function switch. When installing the switch, align the pins, place the right switch on the left switch and secure it by tightening the two screws to 2 Nm (20 in. lbs.). This time, position the switch assembly on the upper side of the column housing and mount it with two screws, tightened to 2 Nm (20 in. lbs.). Connect both cross body wire harness connectors to the switches and then attach the upper and lower shrouds to the steering column, making sure the tabs are in place. Screw the lower shroud to the upper shroud using two screws tightened to 2 Nm (18 in. lbs.). If the vehicle has a tilt steering column, raise it and position it, ensure it is locked, put back the cover over the opening and link up the negative Battery Cable.
Rear Wiper Switch
56007249
Q: How to Maintain a Wiper Switch for Rear Wipers and Washers on Jeep Wrangler?
A:
Before servicing the wiper and washer switch, turn off the supplemental restraint system in vehicles with air bags by unplugging the vehicle's negative Battery Cable for two minutes. Take out the rear wiper and washer switch from the left side of the instrument panel's accessory switch bezel. Turn the control switch bulb holder counterclockwise with a small screwdriver about 30 degrees from the bottom, then remove the bulb holder and bulb unit. During installtion, select the proper bulb size and type to prevent the light from becoming too hot and being damaged. Set the bulb holder and bulb unit over the bulb mounting hole, push so it's firmly in place and twist the holder clockwise about 30 degrees. Put the rear wiper and washer switch back into place in the accessory switch bezel and connect the negative battery terminal.